| |
|
Mylar® Harvest Fresh lidding films are specially designed for fresh cut produce sealant lidding. With superior clarity
and anti-fog properties these films provide unmatched shelf appeal. Easy peel opening and customized seal / peel strength offers consumers the ultimate in convenience.
|
|
To ensure the highest level of food safety Mylar® Harvest Fresh lidding films offer broad FDA and EU regulatory compliance. Strong seals offer tamper evidence. High yield mono web film offer low area cost as well as sustainability
through package reduction. Mylar® Specialty Films commitment to sustainability is evident by offering Mylar® Harvest Fresh lidding with up to 30% Post Consumer Recycle content.
|
|
Mylar® Harvest Fresh lidding films offer superior mechanical properties, such as stiffness and lay flat, providing exceptional machine efficiency. Excellent hot tack provides strong seals even when product is mounded and may also provide increased productivity. Thermal distortion in package is eliminated with the use of Mylar® Harvest Fresh lidding. Mylar® Harvest Fresh lidding can be perforated easily and more precisely then laminates providing optimal respiration of fresh cut produce for extended shelf life.
|
|
Food Contact Status -
Please contact your Mylar® Specialty Films representative to receive the Regulatory Compliance documents
|
|
Disposal of Mylar® HF02AT does not present special disposal problems. It can be buried as a relatively inert material in a landfill or burned in an incinerator with normal refuse. The incinerator should have sufficient draft to exhaust all combustion products through the stack to avoid exposure to irritating fumes. The disposal method should comply with local, state and federal regulations.
|
| Available Thickness [Gauge] |
|
50; 75; 100
|
|
|
| Property |
Thickness |
Value |
Units |
Test |
|
BARRIER
|
| Gas Permeability - O2, 24 hr |
50 |
9 |
cc/100 in² |
ASTM D3985 22℃/75% RH/1 ATM |
| Gas Permeability - O2, 24 hr |
75 |
7 |
cc/100 in² |
ASTM D3985 22℃/75% RH/1 ATM |
| Gas Permeability - O2, 24 hr |
100 |
5 |
cc/100 in² |
ASTM D3985 22℃/75% RH/1 ATM |
| WVTR |
50 |
2.8 |
g/100 in²/day |
ASTM F1249 38℃, 90% RH |
| WVTR |
75 |
1.9 |
g/100 in²/day |
ASTM F1249 38℃, 90% RH |
| WVTR |
100 |
1.3 |
g/100 in²/day |
ASTM F1249 38℃, 90% RH |
|
|
|
PHYSICAL
|
| Elongation at Break MD |
50 - 100 |
110 |
% |
ASTM D882A |
| Elongation at Break TD |
50 - 100 |
80 |
% |
ASTM D882A |
| Modulus |
50 - 100 |
550 |
kpsi |
ASTM D822 |
| Tensile Strength MD (break) |
50 - 100 |
25 |
kpsi |
ASTM D882A |
| Tensile Strength TD (break) |
50 - 100 |
35 |
kpsi |
ASTM D882A |
| Unit Weight |
50 |
12.5 |
lb/ream |
ASTM E252 (0.5 m2) |
| Unit Weight |
75 |
18.5 |
lb/ream |
ASTM E252 (0.5 m2) |
| Unit Weight |
100 |
22.0 |
lb/ream |
ASTM E252 (0.5 m2) |
| Yield (nominal) |
50 |
34,900 |
in²/lb |
|
| Yield (nominal) |
75 |
23,400 |
in²/lb |
|
| Yield (nominal) |
100 |
19,700 |
in²/lb |
|
|
|
Mylar® Specialty Films U.S. Limited Partnership
3600 Discovery Drive
Chester, VA 23836-6436 USA
Tel: (800) 635-4639
Fax: (804) 530-9867
|
Note: These values are typical performance data for Mylar® Specialty Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. Mylar® Specialty Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents.
CAUTION: Do not use in medical applications involving permanent implantation in the human body (Mylar® Specialty Films Medical Policy). For other medical applications, see the Medical Caution Statement. Mylar® Specialty Films accepts no liability for use of it's products in medical applications not reviewed and approved by Mylar® Specialty Films or for product misuse. Mylar® Specialty Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use.
Melinex®, Mylar® and Melinex® STTM are registered trademarks of Mylar® Specialty Films U.S. Limited Partnership.
|
|
Show Printable Version