MYLAR® RL43/RL43AF/RL43AT

Product Description

Mylar® RL43 is a biaxially oriented polyester (OPET) film with an ethylene vinyl acetate (EVA) heat seal layer. It is used as a heat sealable lidding film in packaging frozen and refrigerated foods. Mylar® RL43 is commercially available in nominal 50 and 100 gauges.

Mylar® RL43 is designed to produce strong heat seals to polypropylene (PP). Although designed especially to seal to polypropylene, Mylar® RL43 will produce strong seals to a broad range of container substrates including amorphous polyester (APET, also PETG), semicrystalline polyester (CPET), polyester coated paperboard, polyvinylchloride (PVC), polyethylene (HDPE), and polystryrene (HIPS).

Mylar® RL43 has the same type heat seal layer as Mylar® RL42, but the seal layer is thicker than Mylar® RL42. Mylar® RL43 produces the highest seal strengths to polypropylene of Mylar® lidding films and tends to produce tearing seals to non-polar substrates under chilled conditions. Mylar® RL43 is recommended when light caulking is needed. Mylar® RL43, like other RL types, has a lower seal initiation temperature than lidding films with an amorphous polyester heat seal layer (e.g., Mylar® OL, OL2). This allows good seals to be made at higher line speeds (or using lower sealing temperatures). Mylar® RL43 can withstand freezing temperatures down to -40℉.

Special Features

Corona Treatment (Mylar® RL43T): Selected gauges of Mylar® RL43 are available with corona treatment (on the opposite side of film from the heat seal layer) to enhance printing and laminating. This film type is marketed by Mylar® Specialty Films as Mylar® RL43T. The film is treated to an initial dyne level of 54. The dyne level of treated lidding films may decline with storage, and in-line corona treatment may be required during subsequent printing or laminating to increase the dyne level to a value adequate to get desired ink or laminate adhesion. Standard put-ups for Mylar® RL43T are the same as shown for Mylar® RL43.

Anti-fog (Mylar® RL43AF, RL43AT): Selected gauges of Mylar® RL43 lidding films are available with anti-fogging capability to provide better clarity when stored and displayed in refrigerated conditions. This film type is marketed by Mylar® Specialty Films as RL43AF. Mylar® RL43AF is also available with corona treatment on the opposite side of film from the heat seal layer. This film type is marketed by Mylar® Specialty Films as Mylar® RL43AT.

Approvals

Food Contact Status - Please contact your Mylar® Specialty Films representative to receive the Regulatory Compliance documents

Disposal

Disposal of Mylar® RL43 does not present special disposal problems. It can be buried as a relatively inert material in a landfill or burned in an incinerator with normal refuse. The incinerator should have sufficient draft to exhaust all combustion products through the stack to avoid exposure to irritating fumes. The disposal method should comply with local, state and federal regulations.

Typical Properties

Available Thickness [Gauge] 50;    100;    200

Property Thickness Value Units Test BARRIER Gas Permeability - O2, 24 hr  100  5  cc/100 in²  ASTM D3985 22℃/50% RH/1 ATM  Gas Permeability - O2, 24 hr  200  2.9  cc/100 in²  ASTM D3985 22℃/50% RH/1 ATM  Gas Permeability - O2, 24 hr  50  9  cc/100 in²  ASTM D3985 22℃/50% RH/1 ATM  WVTR  100  1.3  g/100 in²/day  ASTM F1249 38℃, 90% RH  WVTR  200  1  g/100 in²/day  ASTM F1249 38℃, 90% RH  WVTR  50  2.8  g/100 in²/day  ASTM F1249 38℃, 90% RH    PHYSICAL Elongation at Break MD  50 - 200  110  %  ASTM D882A  Elongation at Break TD  50 - 200  80  %  ASTM D882A  Modulus  50 - 200  550  kpsi  ASTM D822  Tensile Strength MD (break)  50 - 200  25  kpsi  ASTM D882A  Tensile Strength TD (break)  50 - 200  35  kpsi  ASTM D882A  Unit Weight  100  26.4  lb/ream  ASTM E252 (0.5 m2)  Unit Weight  200  50  lb/ream  ASTM E252 (0.5 m2)   Unit Weight  50  16.9  lb/ream  ASTM E252 (0.5 m2)  Yield (nominal)  100  16,500  in²/lb    Yield (nominal)  200  8,600  in²/lb    Yield (nominal)  50  26,000  in²/lb

Contact Info

Mylar® Specialty Films U.S. Limited Partnership 3600 Discovery Drive Chester, VA 23836-6436 USA Tel: (800) 635-4639 Fax: (804) 530-9867

Disclaimer

Note: These values are typical performance data for Mylar® Specialty Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. Mylar® Specialty Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents. CAUTION: Do not use in medical applications involving permanent implantation in the human body (Mylar® Specialty Films Medical Policy). For other medical applications, see the Medical Caution Statement. Mylar® Specialty Films accepts no liability for use of it's products in medical applications not reviewed and approved by Mylar® Specialty Films or for product misuse. Mylar® Specialty Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use. Melinex®, Mylar® and Melinex® STTM are registered trademarks of Mylar® Specialty Films U.S. Limited Partnership.