MYLAR® RL31

Product Description
Mylar® RL31 is a biaxially oriented polyester (OPET) with an ethylene vinyl acetate (EVA) heat seal layer. It is used as a heat sealable lidding film in packaging frozen and refrigerated foods. Mylar® RL31 is commercially available in nominal 50 and 100 gauges.

Mylar® RL31 is designed to seal to a broad range of container substrates including amorphous polyester (APET, also PETG), semicrystalline polyester (CPET), polyester coated paperboard, polyvinylchloride (PVC), polyethylene (HDPE), polypropylene (PP), and polystryrene (HIPS).


Heat seals with Mylar® RL31 are stronger than with Mylar® OL, but are still generally strippable from most container substrates. Shredding (film tear or break) can be minimized or eliminated by using higher gauges. Mylar® RL31 has a lower seal initiation temperature than lidding films with an amorphous polyester heat seal layer (e.g., Mylar® OL, OL2). This allows good seals to be made at higher line speeds (or using lower sealing temperatures). Mylar® RL31 is not recommended for applications where "caulking" is required.

Mylar® RL31 can withstand freezing temperatures down to -40℉, and foods can be heated or cooked in contact with this film at temperatures up to 400℉. The oriented polyester base film will begin to distort in the range of 425-450℉.


Special Features
Corona Treatment (Mylar® RL31T): Selected gauges of Mylar® RL31 are available with corona treatment (on the opposite side of film from the heat seal layer) to enhance printing and laminating. This film type is marketed by Mylar® Specialty Films as Mylar® RL31T and is commercially available in nominal 50 and 100 gauges. The film is treated to an initial dyne level of 54. The dyne level of treated lidding films may decline with storage, and in-line corona treatment may be required during subsequent printing or laminating to increase the dyne level to a value adequate to get desired ink or laminate adhesion. Standard put-ups for Mylar® RL31T are the same as shown for Mylar® RL31.

Anti-fog: Mylar® RL31 is not available with anti-fog capability.


Approvals
Food Contact Status - Please contact your Mylar® Specialty Films representative to receive the Regulatory Compliance documents



Disposal
Disposal of Mylar® RL31 does not present special disposal problems. It can be buried as a relatively inert material in a landfill or burned in an incinerator with normal refuse. The incinerator should have sufficient draft to exhaust all combustion products through the stack to avoid exposure to irritating fumes. The disposal method should comply with local, state, and federal regulations.


Typical Properties
Available Thickness [Gauge]
50;    75;    100


Property Thickness Value Units Test
BARRIER
Gas Permeability - O2, 24 hr  100  cc/100 in²  ASTM D3985 22℃/50% RH/1 ATM 
Gas Permeability - O2, 24 hr  50  cc/100 in²  ASTM D3985 22℃/50% RH/1 ATM 
Gas Permeability - O2, 24 hr  75  cc/100 in²  ASTM D3985 22℃/50% RH/1 ATM 
WVTR  100  1.3  g/100 in2/day  ASTM F1249 38℃, 90% RH 
WVTR  50  2.8  g/100 in²/day  ASTM F1249 38℃, 90% RH 
WVTR  75  1.9  g/100 in²/day   ASTM F1249 38℃, 90% RH 
 
PHYSICAL
Elongation at Break MD  50 - 100  110  ASTM D882A 
Elongation at Break TD  50 - 100  80  ASTM D882A 
Tear (Graves)  100  1.1  lb  ASTM D1004 
Tear (Graves)  50  0.7  lb  ASTM D1004 
Tear (Graves)  75  0.9  lb  Tear (Graves) 
Tensile Strength MD (break)  50 - 100  25  kpsi  ASTM D882A 
Tensile Strength TD (break)  50 - 100  35  kpsi  ASTM D882A 
Unit Weight  100  22.2  lb/ream  ASTM E252 (0.5 m2
Unit Weight  50  12.7  lb/ream  ASTM E252 (0.5 m2
Unit Weight  75  18.5  lb/ream  ASTM E252 (0.5 m2
Yield (nominal)  100  19,500  in²/lb   
Yield (nominal)  50  34,400  in²/lb   
Yield (nominal)  75  23,200  in²/lb   



Standard Put-ups
Core I.D. (Inches) Roll O.D. (Inches) Thickness (Gauge) Length (Feet)
3 9 1/2 ± 1/4 50 8,200
3 9 1/2 ± 1/4 75 5,700
3 9 1/2 ± 1/4 100 4,800
3 13 ± 1/4 50 16,500
3 13 ± 1/4 75 11,500
3 13 ± 1/4 100 9,600
6 11 ± 1/4 50 8,200
6 11 ± 1/4 75 5,700
6 11 ± 1/4 100 4,800
6 14 ± 1/4 50 16,100
6 14 ± 1/4 75 11,200
6 14 ± 1/4 100 9,400
6 18 ± 1/4 50 29,600
6 18 ± 1/4 75 20,600
6 18 ± 1/4 100 17,300



Contact Info
Mylar® Specialty Films U.S. Limited Partnership
3600 Discovery Drive
Chester, VA 23836-6436 USA
Tel: (800) 635-4639
Fax: (804) 530-9867



Disclaimer
Note: These values are typical performance data for Mylar® Specialty Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. Mylar® Specialty Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents.

CAUTION: Do not use in medical applications involving permanent implantation in the human body (Mylar® Specialty Films Medical Policy). For other medical applications, see the Medical Caution Statement. Mylar® Specialty Films accepts no liability for use of it's products in medical applications not reviewed and approved by Mylar® Specialty Films or for product misuse. Mylar® Specialty Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use.

Melinex®, Mylar® and Melinex® STTM are registered trademarks of Mylar® Specialty Films U.S. Limited Partnership.