MYLAR® M30

Product Description

Mylar® M30 is a transparent, polyester packaging film, solvent coated on both sides with a PVdC copolymer. The coating is heat sealable and is an excellent moisture and oxygen barrier.

General Product Info

Mylar® M30 can be surface or reverse printed with appropriately formulated inks, and can be combined with other webs by adhesive or extrusion laminating. When printing and adhesive laminating on the coated surface, active solvents such as acetates, ketones and toluene should be removed as completely as possible during drying to avoid adverse effects on coating adhesion. Slow evaporating solvents such as glycol ethers should be completely avoided.

High temperature heat sealing of polymer-coated Mylar® M30 may release small amounts of irritating fumes which should be removed by using area ventilation.

Typical Applications

Mylar® M30 is used both in unsupported form, or as a component of a lamination, and can be run on both form/fill/seal and overwrap equipment. Mylar® M30 is particularly well suited for the packaging of long shelf life or moisture -and oxygen- sensitive products such as processed meats, salty snacks, cakes, candy, nuts, pharmaceuticals and other non-food items.

Approvals

Food Contact Status - Please contact your Mylar® Specialty Films representative to receive the Regulatory Compliance documents.

Disposal

Dispose of in compliance with federal, state and local regulations. Preferred options for disposal are (1) recycling, (2) incineration with energy recovery and (3) landfill. The high fuel value of this product makes option No. 2 very desirable for material that cannot be recycled, but incinerator must be capable of scrubbing out acidic off gases.

Typical Properties

Available Thickness [Gauge] 50;    75;    100

Property Thickness Value Units Test BARRIER Gas Permeability - O2, 24 hr  50 - 100  0.7  cc/100 in²  ASTM D3985 22℃/50% RH/1 ATM  WVTR  50 - 100  0.7  g/100 in²/day  ASTM F1249 38℃, 90% RH    OPTICAL Gloss 20 Degrees  100  180  %  ASTM D2457  Gloss 20 Degrees  50  140  %  ASTM D2457  Gloss 20 Degrees  75  140  %  ASTM D2457  Haze  100  2.5  %  ASTM D1003  Haze  50  7  %  ASTM D1003  Haze  75  8  %  ASTM D1003    PHYSICAL Elongation at Break MD  100  130  %  ASTM D882A  Elongation at Break MD  50  110  %  ASTM D882A  Elongation at Break MD  75  130  %  ASTM D882A  Elongation at Break TD  100  75  %  ASTM D882A  Elongation at Break TD  50  70  %  ASTM D882A  Elongation at Break TD  75  70  %  ASTM D882A  Modulus (Stiffness) MD  50 - 100  500  kpsi  ASTM D822  Tear (Graves)  100  1.1  lb  ASTM D1004  Tear (Graves)  50  0.7  lb  ASTM D1004  Tear (Graves)  75  0.9  lb  ASTM D1004  Tensile Strength MD (break)  100  26  kpsi  ASTM D882A  Tensile Strength MD (break)  50  27  kpsi  ASTM D882A  Tensile Strength MD (break)  75  25  kpsi  ASTM D882A  Tensile Strength TD (break)  100  36  kpsi  ASTM D882A  Tensile Strength TD (break)  50  33  kpsi  ASTM D882A  Tensile Strength TD (break)  75  33  kpsi  ASTM D882A  Unit Weight  100  21.8  lb/ream  ASTM E252 (0.5 m2)  Unit Weight  50  12.3  lb/ream  ASTM E252 (0.5 m2)  Unit Weight  75  18.3  lb/ream  ASTM E252 (0.5 m2)  Yield (nominal)  100  19,800  in²/lb    Yield (nominal)  50  35,400  in²/lb    Yield (nominal)  75  23,600  in²/lb      THERMAL Heat Seal Strength (Coat/Coat)  50 - 100  200  g/in  250℉, 0.5 sec, 20 psi

Standard Put-ups

Core I.D. (Inches) Roll O.D. (Inches) Thickness (Gauge) Length (Feet) 3 9 1/2 ± 1/4 50 9,100 3 9 1/2 ± 1/4 75 6,200 3 9 1/2 ± 1/4 100 5,100 3 13 ± 1/4 50 18,400 3 13 ± 1/4 75 12,400 3 13 ± 1/4 100 10,300 3 18 ± 1/4 50 36,700 3 18 ± 1/4 75 24,700 3 18 ± 1/4 100 20,500 6 11 ± 1/4 50 9,200 6 11 ± 1/4 75 6,200 6 11 ± 1/4 100 5,100 6 14 ± 1/4 50 18,000 6 14 ± 1/4 75 12,100 6 14 ± 1/4 100 10,100 6 18 ± 1/4 50 33,100 6 18 ± 1/4 75 22,300 6 18 ± 1/4 100 18,500 6 22 1/2 ± 1/4 50 54,600 6 22 1/2 ± 1/4 75 36,800 6 22 1/2 ± 1/4 100 30,400 6 24 ± 1/4 50 62,800 6 24 ± 1/4 75 42,300 6 24 ± 1/4 100 35,000

Contact Info

Mylar® Specialty Films U.S. Limited Partnership 3600 Discovery Drive Chester, VA 23836-6436 USA Tel: (800) 635-4639 Fax: (804) 530-9867

Disclaimer

Note: These values are typical performance data for Mylar® Specialty Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. Mylar® Specialty Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents. CAUTION: Do not use in medical applications involving permanent implantation in the human body (Mylar® Specialty Films Medical Policy). For other medical applications, see the Medical Caution Statement. Mylar® Specialty Films accepts no liability for use of it's products in medical applications not reviewed and approved by Mylar® Specialty Films or for product misuse. Mylar® Specialty Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use. Melinex®, Mylar® and Melinex® STTM are registered trademarks of Mylar® Specialty Films U.S. Limited Partnership.