| |
|
Mylar® EB11 is a low gloss polyester film with a matte surface. It is typically used as a carrier film. It is commercially available in nominal 48 - 300 gauge.
|
|
Mylar® EB11 is a low gloss, hazy product. Reverse side printing is superb, and metallized EB11 offers muted matte appearance. EB11 provides an excellent, low gloss surface texture transfer when used as a carrier film.
|
|
Food Contact Status -
Please contact your Mylar® Specialty Films representative to receive the Regulatory Compliance documents
|
| Available Thickness [Gauge] |
|
48; 92; 142; 200; 300
|
|
|
| Property |
Thickness |
Value |
Units |
Test |
|
OPTICAL
|
| Gloss 60 Degrees |
48 |
34 |
% |
ASTM D2457 - 90 |
| Gloss 60 Degrees |
92 |
52 |
% |
ASTM D2457 - 90 |
| Gloss 60 Degrees |
142 |
53 |
% |
ASTM D2457 - 90 |
| Gloss 60 Degrees |
200 |
60 |
% |
ASTM D2457 - 90 |
| Gloss 60 Degrees |
300 |
63 |
% |
ASTM D2457 - 90 |
| Haze |
48 |
55 |
% |
ASTM D1003 |
| Haze |
92 |
65 |
% |
ASTM D1003 |
| Haze |
142 |
70 |
% |
ASTM D1003 |
| Haze |
200 |
77 |
% |
ASTM D1003 |
| Haze |
300 |
85 |
% |
ASTM D1003 |
| Total Light Transmission (TLT) |
48 |
80 |
% |
ASTM D1003 |
| Total Light Transmission (TLT) |
92 |
84 |
% |
ASTM D1003 |
| Total Light Transmission (TLT) |
142 |
83 |
% |
ASTM D1003 |
| Total Light Transmission (TLT) |
200 |
82 |
% |
ASTM D1003 |
| Total Light Transmission (TLT) |
300 |
81 |
% |
ASTM D1003 |
|
|
|
PHYSICAL
|
| Elongation at Break MD |
48 |
100 |
% |
ASTM D882A |
| Elongation at Break MD |
92 |
130 |
% |
ASTM D882A |
| Elongation at Break MD |
142 |
150 |
% |
ASTM D882A |
| Elongation at Break MD |
200 |
155 |
% |
ASTM D882A |
| Elongation at Break MD |
300 |
170 |
% |
ASTM D882A |
| Elongation at Break TD |
48 |
75 |
% |
ASTM D882A |
| Elongation at Break TD |
92 |
75 |
% |
ASTM D882A |
| Elongation at Break TD |
142 |
80 |
% |
ASTM D882A |
| Elongation at Break TD |
200 |
85 |
% |
ASTM D882A |
| Elongation at Break TD |
300 |
100 |
% |
ASTM D882A |
| Tensile Strength MD (break) |
48 - 300 |
19,000 |
psi |
ASTM D882A |
| Tensile Strength TD (break) |
48 - 300 |
29,000 |
psi |
ASTM D882A |
|
|
|
THERMAL
|
| Shrinkage MD (190℃) |
48 - 300 |
3.2 |
% |
Unrestrained @ 190℃/5 min |
| Shrinkage TD (190℃) |
48 - 300 |
2.4 |
% |
Unrestrained @ 190℃/5 min |
|
|
Mylar® Specialty Films U.S. Limited Partnership
3600 Discovery Drive
Chester, VA 23836-6436 USA
Tel: (800) 635-4639
Fax: (804) 530-9867
|
Note: These values are typical performance data for Mylar® Specialty Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. Mylar® Specialty Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents.
CAUTION: Do not use in medical applications involving permanent implantation in the human body (Mylar® Specialty Films Medical Policy). For other medical applications, see the Medical Caution Statement. Mylar® Specialty Films accepts no liability for use of it's products in medical applications not reviewed and approved by Mylar® Specialty Films or for product misuse. Mylar® Specialty Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use.
Melinex®, Mylar® and Melinex® STTM are registered trademarks of Mylar® Specialty Films U.S. Limited Partnership.
|
|
Show Printable Version