MYLAR® EB11

Product Description

Mylar® EB11 is a low gloss polyester film with a matte surface. It is typically used as a carrier film. It is commercially available in nominal 48 - 300 gauge.

General Product Info

Mylar® EB11 is a low gloss, hazy product. Reverse side printing is superb, and metallized EB11 offers muted matte appearance. EB11 provides an excellent, low gloss surface texture transfer when used as a carrier film.

Approvals

Food Contact Status - Please contact your Mylar® Specialty Films representative to receive the Regulatory Compliance documents

Typical Properties

Available Thickness [Gauge] 48;    92;    142;    200;    300

Property Thickness Value Units Test OPTICAL Gloss 60 Degrees  48  34  %  ASTM D2457 - 90  Gloss 60 Degrees  92  52  %  ASTM D2457 - 90  Gloss 60 Degrees  142  53  %  ASTM D2457 - 90  Gloss 60 Degrees  200  60  %  ASTM D2457 - 90  Gloss 60 Degrees  300  63  %  ASTM D2457 - 90  Haze  48  55  %  ASTM D1003  Haze  92  65  %  ASTM D1003  Haze  142  70  %  ASTM D1003  Haze  200  77  %  ASTM D1003  Haze  300  85  %  ASTM D1003  Total Light Transmission (TLT)  48  80  %  ASTM D1003  Total Light Transmission (TLT)  92  84  %  ASTM D1003  Total Light Transmission (TLT)  142  83  %  ASTM D1003  Total Light Transmission (TLT)  200  82  %  ASTM D1003  Total Light Transmission (TLT)  300  81  %  ASTM D1003    PHYSICAL Elongation at Break MD  48  100  %  ASTM D882A  Elongation at Break MD  92  130  %  ASTM D882A  Elongation at Break MD  142  150  %  ASTM D882A  Elongation at Break MD  200  155  %  ASTM D882A  Elongation at Break MD  300  170  %  ASTM D882A  Elongation at Break TD  48  75  %  ASTM D882A  Elongation at Break TD  92  75  %  ASTM D882A  Elongation at Break TD  142  80  %  ASTM D882A  Elongation at Break TD  200  85  %  ASTM D882A  Elongation at Break TD  300  100  %  ASTM D882A  Tensile Strength MD (break)  48 - 300  19,000  psi  ASTM D882A  Tensile Strength TD (break)  48 - 300  29,000  psi  ASTM D882A    THERMAL Shrinkage MD (190℃)  48 - 300  3.2  %  Unrestrained @ 190℃/5 min  Shrinkage TD (190℃)  48 - 300  2.4  %  Unrestrained @ 190℃/5 min

Contact Info

Mylar® Specialty Films U.S. Limited Partnership 3600 Discovery Drive Chester, VA 23836-6436 USA Tel: (800) 635-4639 Fax: (804) 530-9867

Disclaimer

Note: These values are typical performance data for Mylar® Specialty Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. Mylar® Specialty Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents. CAUTION: Do not use in medical applications involving permanent implantation in the human body (Mylar® Specialty Films Medical Policy). For other medical applications, see the Medical Caution Statement. Mylar® Specialty Films accepts no liability for use of it's products in medical applications not reviewed and approved by Mylar® Specialty Films or for product misuse. Mylar® Specialty Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use. Melinex®, Mylar® and Melinex® STTM are registered trademarks of Mylar® Specialty Films U.S. Limited Partnership.