| |
|
Mylar® ADS is a heat stabilized, low shrinkage film with good web handling properties.
|
|
UL Recognition -
Product has been registered with Underwriters Laboratories.
|
| Available Thickness [Gauge] |
|
200; 285; 300; 400; 500
|
|
|
| Property |
Thickness |
Value |
Units |
Test |
|
ELECTRICAL
|
| Breakdown Voltage |
400 |
13.5 |
kV |
ASTM D149 1/4" electrode 500 V/sec 25℃ in air |
|
|
|
OPTICAL
|
| Haze |
200 |
29 |
% |
ASTM D1003 |
| Haze |
300 |
36 |
% |
ASTM D1003 |
| Haze |
400 |
43 |
% |
ASTM D1003 |
| Haze |
500 |
46 |
% |
ASTM D1003 |
| Total Light Transmission (TLT) |
300 |
90.2 |
% |
ASTM D1003 |
|
|
|
PHYSICAL
|
| Density |
300 |
1.395 |
g/cc |
ASTM D1505 |
| Elongation at Break MD |
400 |
160 |
% |
ASTM D882A |
| Elongation at Break TD |
400 |
140 |
% |
ASTM D882A |
| Surface Roughness |
300 |
0.008 |
microns |
DuPont (Ra) 0.80 mm assessment |
| Tensile Modulus MD |
300 |
492,000 |
psi |
ASTM D882A |
| Tensile Modulus TD |
300 |
610,000 |
psi |
ASTM D882A |
| Tensile Strength MD |
300 |
27,700 |
psi |
ASTM D882A |
| Tensile Strength MD |
400 |
25,100 |
psi |
ASTM D882A |
| Tensile Strength MD 5% |
300 |
13,900 |
psi |
ASTM D882A |
| Tensile Strength TD |
300 |
32,600 |
psi |
ASTM D882A |
| Tensile Strength TD |
400 |
27,300 |
psi |
ASTM D882A |
|
|
|
THERMAL
|
| Coefficient of Hygroscopic Expansion |
300 |
7X10^6 |
per % RH |
40% - 80% RH |
| Shrinkage MD (150℃) |
400 |
0.5 |
% |
Unrestrained @ 150℃/30 min |
| Shrinkage MD (190℃) |
300 |
2.5 |
% |
Unrestrained @ 190℃/5 min |
| Shrinkage TD (150℃) |
400 |
0.2 |
% |
Unrestrained @ 150℃/30 min |
| Shrinkage TD (190℃) |
300 |
1.0 |
% |
Unrestrained @ 190℃/5 min |
|
|
Mylar® Specialty Films U.S. Limited Partnership
3600 Discovery Drive
Chester, VA 23836-6436 USA
Tel: (800) 635-4639
Fax: (804) 530-9867
|
Note: These values are typical performance data for Mylar® Specialty Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. Mylar® Specialty Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents.
CAUTION: Do not use in medical applications involving permanent implantation in the human body (Mylar® Specialty Films Medical Policy). For other medical applications, see the Medical Caution Statement. Mylar® Specialty Films accepts no liability for use of it's products in medical applications not reviewed and approved by Mylar® Specialty Films or for product misuse. Mylar® Specialty Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use.
Melinex®, Mylar® and Melinex® STTM are registered trademarks of Mylar® Specialty Films U.S. Limited Partnership.
|
|
Show Printable Version